Home Up Products Saving Energy Glossary Contents About / Contact

The RD Series Inverter / Charger is a new generation modified sine wave inverter designed specifically for renewable energy use. The RD Series is powerful, easy-to-use, and best of all, cost effective.

Power Factor Corrected (PFC) Charger: Our PFC charger is built into all of our inverter chargers. It uses less energy from a generator than a standard charger – using 25-30% less AC current than standard chargers.

Safe and reliable: The RD Series is ETL Listed to the stringent requirements of UL 1741 (USA only), ensuring that the inverter is
safe and reliable.

Easy-to-install: Install the RD Series in four easy steps: simply connect the inverter’s output to your distribution circuits or electrical panel, connect your power cable (AC) to the inverter’s
easy-to-reach terminal block, connect the batteries, and switch on the power

RD Series RD2212 RD1824 RD2824 RD3924
Inverter Specifications  
Input battery voltage range 9 - 16 VDC 18 - 32 VDC 18 - 32 VDC 18 - 32 VDC
Nominal AC output voltage 120 VAC ± 5%
Output frequency and accuracy 60 Hz ± 0.1 Hz
1 msec surge current (amps AC) 60 70 100 150
100 msec surge current (amps AC) 37 40 60 90
5 sec surge power (real watts) 3700 4000 6000 8000
30 sec surge power (real watts) 3450 3300 4800 6400
5 min surge power (real watts) 3100 2850 3950 5800
30 min surge power (real watts) 2400 2400 3500 4750
Continuous power output at 25° C 2200 VA 1800 VA 2800 VA 3900 VA
Maximum continuous input current 293 ADC 120 ADC 186 ADC 260 ADC
Inverter efficiency (peak) 95% 94% 93% 93%
Transfer time 16 msecs
Search mode (typical) 5 watts
No load (120 VAC output, typical) 20 watts 12 watts 19 watts 25 wattts
Waveform Modified Sine Wave
Charger Specifications  
Continuous output at 25° C 110 ADC 50 ADC 80 ADC 105 ADC
Charger efficiency 85% 92%
Power factor > 0.95
Input current at rated output (AC amps) 15 15 21 29
General Features and Capabilities  
Transfer relay capability 2 legs at 30 A for 120 V/30 A or 240 V/60 A service
Five stage charging capability Bulk, Absorb, Float, Equalize (requires remote), and Battery Saver™
Battery temperature compensation Yes, 15 ft Battery Temp Sensor standard
Internal cooling 0 to 120 cfm variable speed drive using dual 92mm brushless DC fans
Overcurrent protection Yes, with two overlapping circuits
Overtemperature protection Yes on transformer, MOSFETS, and battery
Conformal coating on PCB’s for corrosion protection Yes
Powder coated chassis & top for corrosion protection Yes
Stainless steel fasteners for corrosion protection Yes
Listings ETL listed to UL1741 (USA only)
Warranty Two years
Environmental Specifications  
Operating temperature -20° C to +60° C (-4° F to 140° F)
Nonoperating temperature -40° C to +70° C (-40° F to 158° F)
Operating humidity 0 to 95% RH non condensing
Physical Specifications  
Dimensions (h x w x d) 13.75” x 12.65” x 8.0” (34.9 cm x 32.1 cm x 20.3 cm)
Mounting Shelf or wall (vents up)
Weight 37 lb (16.9 kg) 35 lb (15.9 kg) 42 lb (19.0 kg) 53 lb (24.0 kg)
Shipping weight 46 lb (20.9 kg) 44 lb (20.0 kg) 51 lb (23.2 kg) 62 lb (28.1 kg)
Max operating altitude 15,000’ (4570 m)

 

Home Up Products Saving Energy Glossary Contents About / Contact

 

Contact Us: Telephone:  toll free at 1-888-810-4709 Parry Sound,Northern Ontario,Muskoka and Georgian Bay
Send mail to:info@stratenergy.ca  with questions or comments about our product or web site.

Ontario,Canada © Copyright 2013, STRATEnerGY Inc.    All Rights Reserved Caribbean and US
Last modified: April 10, 2017